Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Terblend® N NM-21 EF - (ABS+PA6) - INEOS Styrolution

Check here, which other Terblend N datasheets, application examples or technical articles are available in Material Data Center

Processing/Physical Characteristics - Mechanical properties - Thermal properties - Electrical properties - Other properties - Diagrams

Any use of this information falls under the rules of our disclaimer.

Product Texts

Terblend® N NM-21 EF is an UV stabilised ABS/PA blend providing very high impact strength, even at low temperatures. The enhanced flowability enables excellent processability and surface appearance.

Processing/Physical Characteristics	dry / cond	Unit	Test Standard
ISO Data
Melt volume-flow rate, MVR	60 / *	cm³/10min	ISO 1133
Temperature	240 / *	°C	-
Load	10 / *	kg	-
Molding shrinkage, parallel	0.7 / *	%	ISO 294-4, 2577
Molding shrinkage, normal	0.8 / *	%	ISO 294-4, 2577
Density of melt	928	kg/m³	-
Thermal conductivity of melt	0.156	W/(m K)	-
Spec. heat capacity of melt	2410	J/(kg K)	-
Ejection temperature	90	°C	-

Mechanical properties	dry / cond	Unit	Test Standard
ISO Data
Tensile Modulus	2100 / 1400	MPa	ISO 527
Yield stress	45 / 36	MPa	ISO 527
Yield strain	3.1 / 5	%	ISO 527
Nominal strain at break	25 / 50	%	ISO 527
Charpy impact strength, +23°C	N / N	kJ/m²	ISO 179/1eU
Charpy impact strength, -30°C	N / N	kJ/m²	ISO 179/1eU
Charpy notched impact strength, +23°C	70 / 85	kJ/m²	ISO 179/1eA
Charpy notched impact strength, -30°C	12 / 10	kJ/m²	ISO 179/1eA

Thermal properties	dry / cond	Unit	Test Standard
ISO Data
Temp. of deflection under load, 1.80 MPa	63 / *	°C	ISO 75-1/-2
Temp. of deflection under load, 0.45 MPa	88 / *	°C	ISO 75-1/-2
Vicat softening temperature, B	110 / *	°C	ISO 306
Coeff. of linear therm. expansion, parallel	100 / *	E-6/K	ISO 11359-1/-2
Burning Behav. at 1.5 mm nom. thickn.	HB / *	class	IEC 60695-11-10
Thickness tested	1.6 / *	mm	-
Burning Behav. at thickness h	HB / *	class	IEC 60695-11-10
Thickness tested	3.2 / *	mm	-

Electrical properties	dry / cond	Unit	Test Standard
ISO Data
Relative permittivity, 1MHz	3.4 / 3.8	-	IEC 62631-2-1
Dissipation factor, 1MHz	180 / 900	E-4	IEC 62631-2-1
Volume resistivity	>1E13 / 1E11	Ohm*m	IEC 62631-3-1
Surface resistivity	* / 1E14	Ohm	IEC 62631-3-2

Other properties	dry / cond	Unit	Test Standard
Humidity absorption	1.3 / *	%	Sim. to ISO 62
Density	1070 / -	kg/m³	ISO 1183

Diagrams

Characteristics

Processing

Injection Molding

Delivery form

Pellets

Special Characteristics

Light stabilized or stable to light, U.V. stabilized or stable to weather, Heat stabilized or stable to heat

Regional Availability

North America, Europe, Asia Pacific, South and Central America, Near East/Africa

Other text information

Injection molding

PREPROCESSING
Pre/Post-processing, Pre-drying, Temperature: 80 °C
Pre/Post-processing, Pre-drying, Time: 2 - 4 h

PROCESSING
injection molding, Melt temperature, range: 240 - 270 °C
injection molding, Melt temperature, recommended: 260 °C
injection molding, Mold temperature, range: 40 - 80 °C
injection molding, Mold temperature, recommended: 60 °C

Chemical Media Resistance

Acids
	Nitric Acid (40% by mass) (23°C)
	Sulfuric Acid (38% by mass) (23°C)
	Chromic Acid solution (40% by mass) (23°C)
Ketones
	Acetone (23°C)
Ethers
	Diethyl ether (23°C)
Other
	Ethyl Acetate (23°C)
	Hydrogen peroxide (23°C)

Application examples
Woofer

Disclaimer

Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.

Created: Source: www.materialdatacenter.com

Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.